- internal_constraint_toleranceThe Newton-Raphson process is only deemed converged if the internal constraint is less than this.
C++ Type:double
Controllable:No
Description:The Newton-Raphson process is only deemed converged if the internal constraint is less than this.
- mc_cohesionA TensorMechanicsHardening UserObject that defines hardening of the Mohr-Coulomb cohesion. Physically this should not be negative.
C++ Type:UserObjectName
Controllable:No
Description:A TensorMechanicsHardening UserObject that defines hardening of the Mohr-Coulomb cohesion. Physically this should not be negative.
- mc_dilation_angleA TensorMechanicsHardening UserObject that defines hardening of the Mohr-Coulomb dilation angle (in radians). Usually the dilation angle is not greater than the friction angle, and it is between 0 and Pi/2.
C++ Type:UserObjectName
Controllable:No
Description:A TensorMechanicsHardening UserObject that defines hardening of the Mohr-Coulomb dilation angle (in radians). Usually the dilation angle is not greater than the friction angle, and it is between 0 and Pi/2.
- mc_friction_angleA TensorMechanicsHardening UserObject that defines hardening of the Mohr-Coulomb friction angle (in radians). Physically this should be between 0 and Pi/2.
C++ Type:UserObjectName
Controllable:No
Description:A TensorMechanicsHardening UserObject that defines hardening of the Mohr-Coulomb friction angle (in radians). Physically this should be between 0 and Pi/2.
- yield_function_toleranceIf the yield function is less than this amount, the (stress, internal parameter) are deemed admissible.
C++ Type:double
Controllable:No
Description:If the yield function is less than this amount, the (stress, internal parameter) are deemed admissible.
TensorMechanicsPlasticDruckerPrager
The TensorMechanicsPlasticDruckerPrager has not been documented. The content listed below should be used as a starting point for documenting the class, which includes the typical automatic documentation associated with a MooseObject; however, what is contained is ultimately determined by what is necessary to make the documentation clear for users.
Non-associative Drucker Prager plasticity with no smoothing of the cone tip.
Overview
Example Input File Syntax
Input Parameters
- execute_onTIMESTEP_ENDThe list of flag(s) indicating when this object should be executed, the available options include NONE, INITIAL, LINEAR, NONLINEAR, TIMESTEP_END, TIMESTEP_BEGIN, MULTIAPP_FIXED_POINT_END, MULTIAPP_FIXED_POINT_BEGIN, FINAL, CUSTOM, ALWAYS.
Default:TIMESTEP_END
C++ Type:ExecFlagEnum
Controllable:No
Description:The list of flag(s) indicating when this object should be executed, the available options include NONE, INITIAL, LINEAR, NONLINEAR, TIMESTEP_END, TIMESTEP_BEGIN, MULTIAPP_FIXED_POINT_END, MULTIAPP_FIXED_POINT_BEGIN, FINAL, CUSTOM, ALWAYS.
- mc_interpolation_schemelode_zeroScheme by which the Drucker-Prager cohesion, friction angle and dilation angle are set from the Mohr-Coulomb parameters mc_cohesion, mc_friction_angle and mc_dilation_angle. Consider the DP and MC yield surfaces on the deviatoric (octahedral) plane. Outer_tip: the DP circle touches the outer tips of the MC hex. Inner_tip: the DP circle touches the inner tips of the MC hex. Lode_zero: the DP circle intersects the MC hex at lode angle=0. Inner_edge: the DP circle is the largest circle that wholly fits inside the MC hex. Native: The DP cohesion, friction angle and dilation angle are set equal to the mc_ parameters entered.
Default:lode_zero
C++ Type:MooseEnum
Controllable:No
Description:Scheme by which the Drucker-Prager cohesion, friction angle and dilation angle are set from the Mohr-Coulomb parameters mc_cohesion, mc_friction_angle and mc_dilation_angle. Consider the DP and MC yield surfaces on the deviatoric (octahedral) plane. Outer_tip: the DP circle touches the outer tips of the MC hex. Inner_tip: the DP circle touches the inner tips of the MC hex. Lode_zero: the DP circle intersects the MC hex at lode angle=0. Inner_edge: the DP circle is the largest circle that wholly fits inside the MC hex. Native: The DP cohesion, friction angle and dilation angle are set equal to the mc_ parameters entered.
- prop_getter_suffixAn optional suffix parameter that can be appended to any attempt to retrieve/get material properties. The suffix will be prepended with a '_' character.
C++ Type:MaterialPropertyName
Controllable:No
Description:An optional suffix parameter that can be appended to any attempt to retrieve/get material properties. The suffix will be prepended with a '_' character.
Optional Parameters
- allow_duplicate_execution_on_initialFalseIn the case where this UserObject is depended upon by an initial condition, allow it to be executed twice during the initial setup (once before the IC and again after mesh adaptivity (if applicable).
Default:False
C++ Type:bool
Controllable:No
Description:In the case where this UserObject is depended upon by an initial condition, allow it to be executed twice during the initial setup (once before the IC and again after mesh adaptivity (if applicable).
- control_tagsAdds user-defined labels for accessing object parameters via control logic.
C++ Type:std::vector<std::string>
Controllable:No
Description:Adds user-defined labels for accessing object parameters via control logic.
- enableTrueSet the enabled status of the MooseObject.
Default:True
C++ Type:bool
Controllable:Yes
Description:Set the enabled status of the MooseObject.
- execution_order_group0Execution order groups are executed in increasing order (e.g., the lowest number is executed first). Note that negative group numbers may be used to execute groups before the default (0) group. Please refer to the user object documentation for ordering of user object execution within a group.
Default:0
C++ Type:int
Controllable:No
Description:Execution order groups are executed in increasing order (e.g., the lowest number is executed first). Note that negative group numbers may be used to execute groups before the default (0) group. Please refer to the user object documentation for ordering of user object execution within a group.
- force_postauxFalseForces the UserObject to be executed in POSTAUX
Default:False
C++ Type:bool
Controllable:No
Description:Forces the UserObject to be executed in POSTAUX
- force_preauxFalseForces the UserObject to be executed in PREAUX
Default:False
C++ Type:bool
Controllable:No
Description:Forces the UserObject to be executed in PREAUX
- force_preicFalseForces the UserObject to be executed in PREIC during initial setup
Default:False
C++ Type:bool
Controllable:No
Description:Forces the UserObject to be executed in PREIC during initial setup
- use_displaced_meshFalseWhether or not this object should use the displaced mesh for computation. Note that in the case this is true but no displacements are provided in the Mesh block the undisplaced mesh will still be used.
Default:False
C++ Type:bool
Controllable:No
Description:Whether or not this object should use the displaced mesh for computation. Note that in the case this is true but no displacements are provided in the Mesh block the undisplaced mesh will still be used.